AMERICAN AUDIO V1000 PDF

Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Vot Guzshura
Country: Djibouti
Language: English (Spanish)
Genre: Photos
Published (Last): 24 April 2018
Pages: 127
PDF File Size: 12.83 Mb
ePub File Size: 1.31 Mb
ISBN: 131-8-49212-896-4
Downloads: 81122
Price: Free* [*Free Regsitration Required]
Uploader: Shaktisida

See page 9 for more details on input configuration. Connect a XLR cable to the input of channel one. The speaker wire may be connect by bare wire sudio connected, usually for permanent connectionsbanana plug, or spade connector. Ground Lift Switch This switch is used to disconnect the internal ground signal from the amplifier chassis ground. Dieses Symobl soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen.

American Audio V1000 PLUS Manuals

If the breaker continues to pop, stop using the amplifier and contact customer service. Check the line audi the output terminal of the amplifier to the speaker. P Typical speaker output using spade connectors. Thermal Protection – A single ameerican fan on the Vplus and dual variable speed fans on the Vplus and Vplus V V V amplifiers provide adequate cooling. Insert bare wire into the binding post and tighten. No user serviceable parts inside. Insert the banana jacks into the caps of the binding post, be sure that the banana jack is inserted securely to avoid the risk of it popping out.

In the event of an electrical overload the breaker will pop-out. Cooling Fan – This breaker is designed to protect the amplifier and your speakers americzn the event of an AC overload.

If the “CLIP ” indicator flashes occasionally, the amplifier is approaching its maximum long-term power capacity. Except for an occasional americcan, keep the “CLIP ” indicator dark to avoid overheating the amplifier channel. Cooling Fan Dual speed cooling fans. Use your front gain controls to regulate the output volume.

  ARANGIO RUIZ DIRITTO ROMANO PDF

Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen.

Mono bridge operation connections will follow the above descriptions however, when operating in mono bridge operation the speaker ahdio will run between the two positive red leads. If your speaker lines short, the amplifier automatically detects this problem and discontinues operation for that channel.

Red is positive signal and Black is negative signal. Be sure not to operate your amplifier below the minimum load ratings to reduce the risk of overheating problems.

Please do not return the amplifier to your dealer without contacting customer support. Clipping should be kept to a reasonable minimum.

VLP1000 power amplifier

Antes de usar este amplificador, lea mas advertencias en la guia de operacion. Anerican amplifier is designed to mount into a standard 19″ rack. Risiko – Elektrischer Schlag! When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are tighten down completely.

Diagram 6 Diagram 11 When connecting your speakers to the amplifier using spade connector; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. If the input aydio level is not reduced the built-in limiter will activate.

Low Cut Filter V and V Only – The low-cut filter removes extremely low frequencies from the audio signal amwrican could cause speaker distortion or damage.

The exclamation point triangular symbol is intended to alert the user to the presence of important operating and maintenance servicing instructions in the user manual accompanying the amplifier. However, if it is pushed hard enough to continually light the “CLIP ” indicator, the amplifier’s average output power can reach watts. During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inaudible.

The dip switches on the rear panel allows you to enable or disable the filter for each channel, as well as adjust either a 50Hz or 30 Hz cut-off. An amplifier’s peak current draw at full output power into 2 ohms is several times what the “normal ” draw is, but its various protection circuits will prevent this condition lasting more than a minute or two.

  EPICURO.CARTA SOBRE A FELICIDADE A MENECEU PDF

Amplifiers arrive to you preset in the stereo operation mode. All channel output during the “Short Circuit Protection” will be interrupted i. This fans are used to cool the internal parts of the amplifier when in use.

Um ddas Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. These fans are used to cool the internal parts of the amplifier. Short Circuit Protection can usually be traced back to the signal output line i.

Please read and understand this manual completely before attempting to operate your new amplifier. Connect an input signal to channel one. The lightning flash with an arrow triangular symbol is intended to alert the user to the presence of non insulated “dangerous voltage” within the products enclosure, and may be of sufficient magnitude to constitute a risk of electric shock.

It will allow brief clipping of peaks and will only activate when continuous, hard clipping occurs. Low Cut Frequency Selector When the Low Cut Filter is activated, dip switches 2 channel 1 and 3 channel 2 will control the frequency roll-off. Apply an input source signal to your amplifier.

VLP power amplifier – Amplifier – Audio – Products – ADJ Group

Under heavy clipping activity lower the channel one gain control to reduce there details on input configuration. Carefully check the shipping carton for damage that may have occurred during shipping.

Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response. Never block the fan grills in any anerican or mount in an enclose rack, doing so may cause the amplifier to overheat and fail.