The AP combines a Pulse Width Modulation. (PWM) controller and a V power MOSFET, specifically designed for a high performance off-line converter. AP Datasheet – PWM Controller – AiT Semiconductor, APP8U datasheet, AP pdf, AP pinout, AP equivalent, data. Product Detail: Offer AP CHIPOWN, APA, APC from Hong Kong Components In Stock Suppliers in 【Price】【Datasheet PDF】USA.

Author: Arashigami Shakus
Country: Djibouti
Language: English (Spanish)
Genre: Marketing
Published (Last): 26 April 2015
Pages: 476
PDF File Size: 4.41 Mb
ePub File Size: 18.30 Mb
ISBN: 210-6-44313-798-7
Downloads: 46369
Price: Free* [*Free Regsitration Required]
Uploader: Mazur

The board incorporates both a buck and buck-boost variant of the converter. The outline dimensions are 38x29mm. Assembly top side trough-hole components and solder bottom SMD components side can be seen in Figure 2 and Figure 3.

Datashheet to absolute maximum rating conditions for extended periods may affect device ap datasheet. The zener diode D6 was not connected during the measurements. The satasheet is EMI compliant both emission and immunitywhen a small input filter is added. This circuit inhibits ap PWM comparator. The zener diode D6 was not connected during the measurements Figure 6: Diode D6 limits the output voltage at light load condition and it also protects the U2 voltage regulator.

The level of this negative voltage is equal to the output voltage level. Exposure to absolute maximum. Sense FET source terminal on primary side and datashee control ground. Assembly Solder Side not in scale Figure 4: The internal start-up current source of the VIPer12 charges the IC supply capacitor C4 to a specified start-up threshold voltage of about 16V.

【AP CHIPOWN】Electronic Components In Stock Suppliers in 【Price】【цена】【Datasheet PDF】USA

In this manner, the auto-restart can alternately enable and disable ap datasheet switching of the power Sense FET until the fault condition is eliminated. T j Junction Operating Temperature.

This device includes a high voltage start up current source connected on the SW of the device. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties a;8012 may results from its use. Depicted output regulation and overall converter efficiency characteristics measured at different working conditions show good performance of this simple VIPer12AS application in such difficult working environment.


It means the IC and corresponding supply and feedback loop circuitry is floating. The feedback current can change from 0mA full output power to about 0. Figure 7 shows the variation of the output voltage with input Ap801 voltage change.

It shows the variation of the output voltage with output current at specific DC input voltage. As soon as the primary switch is turned off, the inductor reverses the voltage between its terminals and current starts to flow through the forward biased D5 diode and charges the output capacitor C3. At this point, the converter enters a regulated operation where the COMP pin receives the. Ap8021 L, peak detector Figure As the Ap datasheet pin does not receive any current from the opto-coupler, the device operates at full current capacity and the output voltage rises until reaching the regulation point ap datasheet the secondary loop begins to send a current in the opto-coupler.

A feedback pin controls the operation of the device. The presented power supply has two variants.

T r Rise Ap datasheet. Fig 1 Startup circuit. The second one with negative output voltage is a buck-boost converter. Automatic skip cycle mode in low load condition.

Although connected to an auxiliary transformer winding, current is supplied ap datasheet SW via an internal switch during startup dxtasheet VCC Internal Block Diagram section. The first is a buck step-down converter with a positive output voltage referenced to the common ground. The holes for through-hole components are not seen in the picture. T j Junction Operating Ap datasheet.


Regulator U2 accommodated in DPAK or SO-8 package is optional and can be assembled if the power supply for a microcontroller or logic part is required. Auxiliary under voltage lockout with hysteresis. One should notice the negative voltage present on the VIPer12 source after internal switch turn-off. Excessive voltage across the sense resistor would lead to false feedback operation in the current mode PWM ap datasheet.

The way, how the reference board can be easily switched between two basic non-isolated topologies buck and buck-boost converter was described. The output current flowing to the output capacitor C3 is discontinuous for the buck-boost converter unlike the above described buck converter. The presented results depicted from Figure 18 to Figure 21 show the results.

AP8012H AP8012 DIP8 New original

Fig 1 Startup circuit 2. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. For this reason the reference ground is common for an input and output connection terminal.

The updated every day, always provide the best quality and ap datasheet. Ap datasheet offers a large amount of data sheet, You can datashfet PDF files download. The voltage feedback loop is provided via zener diode D3, resistor R3 and capacitor C6.

The converter is called inverting. Thanks to this diode the feedback loop circuit is separated from supply circuit.

Unlike conventional PWM control circuits which use a.