ASTM A90 PDF

ASTM A90/A90M(). Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings. ASTM A ZINC PLATING WEIGHT ON STEEL. This test method covers procedures for determining the weight [mass] of coating on iron or steel sheet, wire, and. A. ASTM A90 – Standards Test Method for Weight of Coating on F. ASTM A — Steel Sheet, Zinc Coated (Galvanized) or Zinc-Iron Alloy.

Author: Toshakar Kagakora
Country: Bermuda
Language: English (Spanish)
Genre: History
Published (Last): 21 November 2014
Pages: 53
PDF File Size: 8.47 Mb
ePub File Size: 20.9 Mb
ISBN: 477-3-65921-447-3
Downloads: 33357
Price: Free* [*Free Regsitration Required]
Uploader: Vudozshura

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

Originally approved in SR means the standard deviation for R reproducibility.

After stripping, wash the specimens by scrubbing them under running aatm, dip in hot water, and wipe or blow dry. The specimen of wire may be of any length over 12 in. A coating of zinc on iron or steel articles provides protection against corrosion.

ASTM A90/A90M 13镀锌和镀锌合金钢铁制品镀层重量的试验方法_百度文库

Certain portions of the procedure involving determination of specimen weight [mass] have traditionally been performed in SI units, and corresponding inch-pound units are not included.

Where a continuous length is not available, shorter lengths totaling over 12 in. Each of ten laboratories tested three replicates of two different materials. If specimens were prepared to the dimensions as provided in Note 2, they shall be presumed to have an area of 5.

Certain portions of the procedure involving determination of specimen weight [mass] have traditionally been performed in SI units, and corresponding inch-pound units are not included. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Alternatively, for specimens of uniform thickness of base metal, such as a piece of plate or pipe, determine the average thickness of the stripped specimen to the nearest 0.

  ANISHA LAKHANI SCHOOLED PDF

Unless otherwise indicated, it is intended that all reagents shall conform to the speci? As a9 protection is provided by sacri? This requires about 15 to 30 s, except in the case of sherardized coatings, which require a somewhat longer time. This standard has been approved for use by agencies of the Department of Defense.

ASTM A90/A90M – 13(2018)

No further reproductions authorized. Link to Aetm This link will always route to the current Active version of the standard. Coating weights [masses] on all zinc-coated articles other z90 sheets are expressed in weight [mass] per unit area of surface. Determine the weight [mass] of the specimens again, to the same precision as in the initial determination.

Your a9 will receive careful consideration at a meeting of the responsible technical committee, which you may attend. In the body of this test method, reference to zinc coating shall be interpreted to also include zinc alloy coating except where speci?

Except as otherwise provided, the specimens should have a minimum area of 3 in. The same solution may be used repeatedly until the time required for stripping becomes inconveniently long. Hydrochloric acid fumes are present, and hydrogen gas is evolved in the stripping process. Since the density of the steel is known 0. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every?

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. The weight [mass] of coating in grams on a specimen of that area is numerically equal to the weight [mass] of coating in ounces per square foot of sheet. Specifications for zinc-coated articles frequently provide for different classes of coating so that the purchaser can select the coating weight [mass] most suitable to his needs.

ASTM A90 – ZINC PLATING WEIGHT ON STEEL

For very small items, several pieces may have to be stripped to obtain the minimum area. The mixing should be performed under an acid fume hood.

  HOW TO SAVE A TYPEABLE PDF

Current edition approved April 1, Under no circumstances should the water be added to the acid. As the protection is provided by sacrificial loss of zinc, the degree of protection is proportional to the weight [mass] of zinc coating.

It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. After determining the weight [mass], immerse aa90 specimen singly in the stripping solution and allow to remain until the violent evolution of hydrogen has ceased, and only a few bubbles are being evolved.

A number in parentheses indicates the year of last reapproval. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

When it is not possible to determine the area accurately, as in specimens from corrugated sheets, the thickness of the stripped sheet shall be determined to the nearest 0. Mixing must be done by slowly adding sulfuric acid to water due to the heat generated and possible splashing. Permission rights to photocopy the standard may also be secured from awtm ASTM website www.

For specific hazards statements see 5. A coating of zinc on iron or steel articles provides protection against corrosion. Therefore, the test should be performed under conditions of adequate ventilation.

In the body of this test method, reference to zinc coating shall be interpreted to also include zinc alloy coating except where specifically stated otherwise.

A fume hood is recommended for large numbers of samples or where the test is to be carried out frequently asym extended periods of time.

Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. For results to be reported in metric units, the specimen should have an area of mm2 of sheet