ATTANSIC ATTP1 PDF

, 13, ATTANSIC, -. Kring Electronics Co., Ltd. , -, Attansic, sop8. 63, 0, ATTANSIC, -. Rantle East Electronic. , -, ATTANSIC, SOP. 年12月11日 ATTP1_ – Technology Corporation ATTP1 Over Temperature Please contact Attansic Technology Corp. for the latest documents. Attansic. ATTP1. Tel:. MFG:. ATTANSIC. Picture. D/C:. 09+. QTY:. Packaging:. SOP8L. Package:. Note:. 原装正品. Support. No“ATTP1”Picture.

Author: Zulumi Sar
Country: Sierra Leone
Language: English (Spanish)
Genre: Politics
Published (Last): 12 August 2006
Pages: 239
PDF File Size: 4.45 Mb
ePub File Size: 8.14 Mb
ISBN: 884-7-90088-309-7
Downloads: 56436
Price: Free* [*Free Regsitration Required]
Uploader: Vumi

Well, I’ve solved that problem. You should thread the jumper first, then solder to the Attansic chip, then finally solder to the Winbond chip. I will have no sympathy. It is the 4th pin from the top right corner of the chip going wttp1 the right side of the chip, when viewed as described above.

ATTP1(ATTANSIC,SOP-8), DataSheet|Picture – Electronic Parts – Censtry Electronics Co.,Ltd.

This is the analog voltage input. Also note that, because you are now monitoring the thermal diode directly, the thermistor in the socket is now rather pointless. If I understand your question correctly, then to restore the mobo back to default, you simply have to remove the mod. I’ve been looking for developer’s docs for the NF2 chipset and haven’t been able to find any. I’ve got pretty steady hands and it took me three tries to get the jumper soldered correctly without bridging solder to the other pins.

Run a jumper from pin 61 of the Winbond chip to pin This is the 5vsb input. Lift this pin just as you did pin That is one of the reasons I did it the way I did, so that you could undo it if necessary.

ATTP1 Attansic CPU thermal protection controller chip SOP8

So what is the solution? I’ve personally verified this a few times myself, so I know it works. Find pin 97 of atyp1 Winbond chip. The wire will need to be about 8 cm 3″ long. It is more likely that you will mess it up such that the OTP function trips prematurely and you aren’t able to power on the computer at all. Solder to pin 61 first, then pin How to test OTP? Our members offer you their FAQs!

  GOSPODAR PRSTENOVA DRUZINA PRSTENA KNJIGA PDF

I just have you solder directly to the pin because it is simpler to explain. Check out our sister site! As for the agtp1, yes you should solder pin 4 of the Attansic back down to the mobo. The time now is These attanslc are VERY delicate! I use to type attansiic short sentence. You will need to carefully lift this pin from the solder pad. As a result, when you tie the Temp 3 input to the thermal diode while the Attansic chip is hooked up, it causes the Attansic chip to think that the CPU artansic exceeded safe temp limits.

In my case, I actually took a chance with my CPU to try it out. This connects to channel two of the Winbond atrp1, which means you can now use channel two on pin for something else. The jumper wire will need to be about 3. Find pin of the Winbond chip. I believe the AN7 has a thermal probe under the north bridge. BB code is On. Make sure you leave just a dollop of solder on the end of the jumper wire when you tin it or you’ll never get it to solder properly but don’t leave too much, or you’ll bridge the pins.

Also make sure that you don’t accidentally bridge any of the adjacent pins with solder while you are trying to lift this pin. I didn’t think it did. Add Thread to del. If you muck this up and turn your board into a doorstop, don’t come crying to me. Tatp1 means that your poor CPU is going to blow its brains out just as soon as it loses proper cooling for any reason.

  HP2211 DATASHEET PDF

However, be aware that soldering pin 97 and pin back down is atansic tricky because of the fine spacing of the pins. It didn’t change my temp readings at all, but it is theoretically possible for there to be a slight change in the reading. You will find that it is easiest to thread the jumper on the diagonal under the Atttansic socket between the pins.

When the PSU is shutdown or in standby, this rail is dead, and all of the items connected to the monitor inputs are no longer in a high impedance state. The possibilities are endless!

While this mod works pretty well, it has one glaring drawback, which I mentioned in the previous post: You don’t need to move the jumper though. Webb City, Mo Posts: That’s all there is to it. However, because of the way the mod is done, the odds of messing it up in such a way that you dissable the OTP function are pretty low. If you have previously modded your mobo to read the thermal diode, you MAY find that your temps are degrees higher than they used to be.

Tie the analog voltage supply for the Winbond chip to the 5vsb rail instead of the 5v rail. Anything else is nearly impossible. This is the top right pin on the Attansic chip, when viewed with the mobo oriented as described above.